Search
Cases
Search cases
Clear
⌘K
All
8
Solved
6
Open
0
Troubleshooting
Incident analysis
Procedure
Knowledge
8 cases match
Equipment
All
Main Engine
Auxiliary Engine
Turbocharger
Boiler
Purifier
Compressed Air
Pumps
Fresh Water Generator
OWS & Bilge
Incinerator & Sewage
Refrigeration & HVAC
Steering Gear
Propulsion & Thrusters
Deck Machinery
Ballast System
Electrical
Automation / PLC
Navigation
Fire & Safety
Other
Sort
Best match
Newest first
Highest rated
Most confirmed
Recently updated
Apply
▲
0
rating
0
comments
Aalborg boiler will not light after changeover from HFO to MDO
Troubleshooting
Boiler
·
Aalborg composite boiler
·
Flame out
After changeover from heavy fuel to MDO, the burner did not light. At each start it tripped on flame out.
Anonymous · 6 y
▲
0
rating
0
comments
HFO transfer pump: start relay chatters, pump will not start in manual
Troubleshooting
Pumps
When Start is pressed, relay 4 in the starter crackles and buzzes. The main contactor does not pull in. The main contactor is new. With one output wire of the control circuit disconnected, the pump…
Anonymous · 2 y
▲
0
rating
0
comments
HFO to MGO changeover: cool slowly and watch viscosity
Procedure
Main Engine
Changing the main engine and diesel generators from HFO to MGO is safe if fuel temperature falls slowly and viscosity stays between 2 cSt and 20 cSt. This is the general procedure I use; it follows…
Anonymous · 3 y
▲
0
rating
0
comments
Alfa Laval SA 836: oil comes out of the bowl water feed pipe
Troubleshooting
Purifier
·
Alfa Laval SA 836
·
Oil leaking from bowl
At start, after some time, heavy fuel oil came out of the pipe that feeds water into the bowl. No pressure on PT4 and PT5 (oil and water outlets). Alarm "Oil leaking from bowl".
Anonymous · 6 y
▲
0
rating
0
comments
Siemens LOGO! fuel changeover: program loaded but does not run
Troubleshooting
Automation / PLC
·
Siemens LOGO! 230RC with DM8 230R and AM2 expansion modules
·
Control fail
The automatic HFO/MDO changeover (valves and fuel heating) is controlled by a Siemens LOGO! 230RC with expansion modules. A "Control fail" alarm came up on the fuel page of the control PC. Expansion…
Anonymous · 3 y
▲
0
rating
0
comments
Fuel treatment chemicals: why engine makers prefer good fuel management
Knowledge
Main Engine
The big makers of main and generator engines prefer good fuel management to fuel treatment chemicals; they have not confirmed the claimed benefits of additives. The one exception I make is a…
Anonymous · 4 y
▲
0
rating
0
comments
Main engine: gas bubbles in the fuel system, fuel pressure jumping
Troubleshooting
Main Engine
Air (gas) bubbles in the main engine fuel oil system. Small bubbles stayed all the time. Fuel pressure was jumping.
Anonymous · 1 y
▲
0
rating
0
comments
Aux boiler explosion: waxy MGO, then fan restart into a gassy furnace (Manhattan Bridge)
Incident
Boiler
·
""
·
Aux boiler emergency trip (Furnace flame-eye abnormal)
A 13,900 TEU container ship was berthing at Felixstowe in winter. The auxiliary boiler (rotary cup burner) had been on MGO for three days for the ECA. It tripped four times between 17:30 and 19:51.…
Anonymous · 8 y
EngineLog
Home
Cases
Assistant
Library
Log in
Join
Home
Cases
Assistant
Library